Vehicles
326 not categorized PORSCHE 356 C PRE ACan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
$160.00
Make a selection
$5.49
Make a selection 021919081D View/Change Diagram
From $5.00
Make a selection 021119957 This is an autoatlanta exclusive oil pressure switch boot for all 914-4 models. believe it or not your 914 had this factory installed. long gone on most engines by now this part is critical to seal in the cooling air. easily installed, this part fits behind the distributor. please check the oil pressure switch for leaks at the same time. View/Change Diagram
$13.00
Make a selection 039906051 Our rebuilt fuel injection components are the highest quality available and replace no longer available parts. Your 914 fuel injection can again operate as it should for snappy performance, great gas mileage, and long engine life. The manifold pressure sensor is notorious for diaphragm failure resulting in a rich mixture black sooty exhaust and a poor warm idle. please evacuate to check this part. if it will not hold vacuum it is bad. rebuilt by the leading Bosch injection company in the nation you can be assured of a perfect calibration. purchase the 037 European sensor for extra top end performance along with the factory temperature sensor resistor. There is a core charge, which is refundable upon receivi...(choose a part on the right to read more) View/Change Diagram
From $359.00
Make a selection 10002870 Each 100 series brake pad is a true oe formulation, manufactured using oe processes and oe materials by oe manufacturers. All centric parts friction is designed to meet or exceed our exacting standards for o.e. Braking performance. Centric 100 series brake pads feature fine blank or precision blank backing plates with machined abutments for proper caliper fitment. All 100 series brake pads are manufactured using oe positive mold technology for consistent friction material density throughout the pad, resulting in even wear and performance characteristics throughout the life of the product. General Fitment911 1984-86911 1987-89 911 1989-94
$53.46
Make a selection 047260849 A/c compressor drive belt, 13 x 900 mm View/Change Diagram
$13.50
Make a selection 10002880 Each 100 series brake pad is a true oe formulation, manufactured using oe processes and oe materials by oe manufacturers. All centric parts friction is designed to meet or exceed our exacting standards for o.e. Braking performance. Centric 100 series brake pads feature fine blank or precision blank backing plates with machined abutments for proper caliper fitment. All 100 series brake pads are manufactured using oe positive mold technology for consistent friction material density throughout the pad, resulting in even wear and performance characteristics throughout the life of the product. General Fitment911 1984-86911 1987-89 911 1989-94
$40.50
Make a selection 100174094 The name mahle is synonymous with both Porsche and performance. From the engineering of the world’s first aluminum alloy piston, to the development of the nikasil coated cylinders (nikasil is the wear-resistant cylinder coating now used throughout the industry), the mahle tradition powers not only Porsche street cars, but also today’s most advanced Porsche racecars. If you want more horsepower out of a daily driver, or ultimate performance for a full-on racecar, mahle pistons and cylinders can handle it. These cylinder and piston sets feature nikasiltm coated cylinders which reduce wear and a matched aluminum piston in several different compression rations. Includes rings and wrist pins. General Fitment911 1974-77
$850.00
Make a selection 1248208310 2 bar low pressure and 30 bar high pressure binary switch. This switch is designed to be compatible with r-12 and r134a refrigerants. Located on reciever-drier with 2 spade terminals. Used for compressor cut-out. General Fitment924 1980-85924 1976-79
From $12.67
Make a selection 12537007 Centric parts high carbon alloy brake rotors feature a double disc ground finish which virtually eliminates run out and any disc thickness variation issues. Double disc grinding also produces a non-directional finish for improved rotor and pad break-in. The surface roughness production standard for centric high carbon brake rotors: rms=64.3 or ra=1.6 micro-meters (63 micro-inches). General Fitment924 1980-85924 1986-88 928 1978-82 928 1983-86 944 1982-85 944 1985-88
$139.73
Make a selection 12533091 Centric parts high carbon alloy brake rotors feature a double disc ground finish which virtually eliminates run out and any disc thickness variation issues. Double disc grinding also produces a non-directional finish for improved rotor and pad break-in. The surface roughness production standard for centric high carbon brake rotors: rms=64.3 or ra=1.6 micro-meters (63 micro-inches). General FitmentCAYENNE 2003-06CAYENNE 2007-10 CAYENNE 2011-14
$145.13
Make a selection 12533078 Centric parts high carbon alloy brake rotors feature a double disc ground finish which virtually eliminates run out and any disc thickness variation issues. Double disc grinding also produces a non-directional finish for improved rotor and pad break-in. The surface roughness production standard for centric high carbon brake rotors: rms=64.3 or ra=1.6 micro-meters (63 micro-inches). General FitmentCAYENNE 2003-06CAYENNE 2007-10 CAYENNE 2011-14
$110.03
Make a selection 170111184
General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89
$741.40
Make a selection 150752 As we all know the only way to install the optional oil pressure gauge is to replace the oil pressure switch with the much "fatter" oil pressure sender. this cannot be accomplished without cutting the sheet metal or extending the hole out of the sheet metal and attaching the sending unit. this hose will give you the needed length. (might need to grind down the male end for a proper fit) General Fitment914 1970-76
$37.95
Make a selection 274049 Designed for air-cooled 911 engines with a nickel ceramic bore, these pistons are machined from forged 2618 alloy for greater strength. The valve pockets are machined to accommodate high lift cams and accept the stock stroke and rod length. The ring grooves are precision cnc machined for OEM style rings (included). Set of 6. General Fitment911 1978-83
$1,694.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |